Snowmobiles have been a favorite mode of transportation for many Canadians, but they are also known to produce a lot of noise when in use. The stator is the fan-like part that creates energy from an electric current and cools down the output so it can be used efficiently by your snowmobile engine. If you notice it making grinding noises or if its getting louder than usual, then replacing your snowmobile stator might be necessary.
If your snowmobile stator is bad, you will see symptoms such as the engine will not start, or it will be hard to start. If you have a battery that is too weak to power the machine, then there may be an issue with the stator.
Runs poorly at low rpms yet well at higher rpms (Low speed coil going bad) At lower rpms, it’s OK, but at higher rpms, it’s a disaster (High speed coil is going bad) It’s backfiring and won’t run properly. Throughout the day, the sled gradually loses power.
Also, what happens if the stator fails?
On small engines, the stator coil produces the power for the spark plug and other accessories. There would be no spark without a stator, and the engine would not function. When a stator fails, it produces a weak spark, which causes the engine to miss or perform badly. As the engine heats up, the symptoms usually intensify.
Subsequently, question is, how much does it cost to fix a stator? Stator & Rotor – $250 – $1,500 for a new set A new stator and rotor set typically costs between $250 and $1,500. They are stationary and rotating parts of any system that generates electricity. When they stop working seamlessly, they need repair or replacement.
So, what are the signs of a malfunctioning Polaris CDI box?
So, your CDI-equipped motorbike has a spark issue. Misfiring, dead cylinders, backfiring, strange tach behavior, and a slew of other issues with your engine’s operation are all possible symptoms. As the bike heats up, the issue may worsen. It may not even be able to maintain low rpm.
What causes the stator to fail?
Unequal voltage between phases might cause insulation to deteriorate thermally in one phase of the stator winding. Unbalanced loads on the power supply, a bad connection at the motor terminal, or a high resistance contact are the most common causes of unequal voltages (weak spring).
Answers to Related Questions
How do you put a stator to the test?
Perform the static stator testing first. Disconnect the regulator from the stator when the ignition switch is turned off. Insert one probe into one of the stator pin sockets and set the multimeter to “Resistance” or “Ohms” on the lowest scale. Make contact with any chassis ground with the other probe.
Is it possible for a defective stator to backfire?
The ignition coils on a stator have nothing to do with the AC power windings. At lower rpms, it’s OK, but at higher rpms, it’s a disaster (High speed coil is going bad) It’s backfiring and won’t run properly. Throughout the day, the sled gradually loses power.
Is it possible to rebuild a stator?
All refurbished stators come with a one-year replacement guarantee and need a core swap. Although most new and rebuilt stators are produced to stock specifications, we do offer several high output stator variants as part of the Hot Shot Series to help you get even more electrical power out of your machine.
What are the signs and symptoms of a faulty voltage regulator?
A defective instrument voltage regulator usually causes a few indications that alert the driver to a problem.
- Gauges that are dim or flickering. Dim or flickering gauges are one of the first signs of a voltage regulator problem.
- Readings that are inaccurate or irregular.
- Instrument cluster is not working.
What is the purpose of a stator?
The stator generates a revolving magnetic field that powers the spinning armature in an electric motor, whereas the stator transforms the rotating magnetic field to electric current in a generator. The stator directs the flow of fluid to or from the spinning element of the system in fluid-powered devices.
How do you use a multimeter to examine a snowmobile coil?
Turn the measuring dial on the digital multimeter to the resistance setting after turning it on. The capital Greek letter omega denotes resistance in ohms, which is shown on the dial. Connect the multimeter’s red (positive) probe to the ignition coil’s positive, outside post.
What is the best way to test a CDI ignition coil?
Check for resistance using your multimeter. For Ohms, it should be in the thousands. You may now test your ignition coil whether your plug wires and caps are in good shape. First, determine the resistance between the CDI box’s main wire and the ground or ground wire.
On a snowmobile, where is the stator?
Overheated snowmobile stators are prone to failure. Inside the motor, a snowmobile stator is installed (on some models, in a bath of engine oil, on others, dry), which is an extremely hot environment to be operating in!
What causes a stator to malfunction?
The failure of a stator may be caused by a number of factors. When using accessories, the burden is too heavy (winch,heated grips,headlights, etc). You would overwhelm the system if you worked on multiple of these things at once (plowing/pulling/possibly trapped at night). This may cause the stator or rectifier to overheat.
When a rectifier burns out, what causes it to do so?
Failure Causes in General
The regulator rectifier might fail for a variety of reasons. Ground connections are critical for adequate voltage, because a poor voltage might cause the regulator rectifier to overheat. Defective voltage is caused by faulty grounding, corroded battery connections, and weak or loose battery connections.
What causes the spark plug to not ignite?
Anything that inhibits coil voltage from leaping the electrode gap at the end of the spark plug causes spark loss. This includes spark plugs that are worn, fouled, or broken, as well as defective plug wires and a fractured distributor cover.
How much voltage should a stator produce?
The goal of this test is to determine if the stator can generate enough AC voltage at 1000 RPM. A 32-amp stator, for example, should produce 18 volts AC (VAC) every 1000 RPM. It should be 36 VAC in the year 2000. (18×2). It should be 54 VAC at 3000 RPM (18 X 3).
Is it possible for a CDI box to create a weak spark?
Yes, a faulty cdi may result in a weak spark.
Is a battery required for CDI ignition?
CDI ignition: Most dirt bikes utilize this ignition since it can start a motorbike without a battery. Because a dirt bike has no lights or horn, it does not need a battery to power these electrical components.
What is the purpose of the ignition control module?
It regulates the firing time of the ignition coil. The ignition control module is the brains of the ignition system of a car. It controls the ignition of the engine’s spark plugs. The ignition control module is reliant on the automobile battery for the’spark’ that starts the ignition system.
Is it possible to circumvent a CDI box?
Motorcycles, turbine-powered aircraft, outboard motors, and certain autos employ a capacitor discharge ignition box (CDI). For debugging reasons, you may temporarily bypass a CDI box. As a result, it is unable to maintain sufficient voltage to keep the engine running.
